«Equipment and technologies for oil and gas complex»

Modernization and improvement of the pumping equipment operational life-time with account of operating conditions analysis

UDC: 621.671
DOI: 10.33285/1999-6934-2022-2(128)-19-23

Authors:

¹ Ingush State University, Magas, Russian Federation

Keywords: centrifugal pump, mechanical engineering, development, pumped medium, vertical unit, modernization, increased resource, operational conditions

Annotation:

The presented article discusses the modernization and increase in the resource of the vertical electric pumping unit, designed for pumping technical contaminated water. The current processes of the world economy globalization are determined by the progress of science and technology. The country's position in the modern world today is increasingly determined by the quality of human capital, the state of education and the degree of using science and technology in production. There is another definition of the industry technological modernization as a form of realizing the competitiveness of various economic systems formed by updating the production apparatus, replacing obsolete equipment and technologies in the sphere of material production with modern, more efficient ones. This definition is more consistent with the Russian economy realities, since it takes into account the process of renewal, and not only the introduction of technological innovations. The aim of the modernization is to increase the service life of the pump, to reduce the cost of its maintenance, to increase the environmental friendliness and safety of production. The main requirements for pumping equipment are reliability and ease of use, cost-effectiveness. At present, the requirements for the reliability and safety of the equipment pumping various chemical (toxic, explosive, abrasive, crystallizing, etc.) media are constantly increasing. Therefore, the old pumping equipment requires modernization or complete replacement.

Bibliography:

1. Golubev A.I. Tortsovye uplotneniya vrashchayushchikhsya valov. – Izd. 2-e, pererab. i dop. – M.: Mashinostroenie, 1974. – 212 s.
2. Dzarmotov S.I. Razrabotka sistemy okhlazhdeniya tortsovogo uplotneniya perekachivaemoy tsentrobezhnym nasosom sredoy s abrazivami // Innovatsionnye nauchnye issledovaniya v sovremennom mire: sb. tr. po materialam IV Vseros. konkursa nauch.-issled. rabot, Ufa, 20 apr. – Ufa, 2021. – S. 19–29.
3. Danilevskiy V.V. Tekhnologiya mashinostroeniya. – M.: Vysshaya shk., 1984. – 416 s.
4. Karakhan'yan V.K., Kostyuk A.V. Stoimost' zhiznennogo tsikla nasosa (LCC): rukovodstvo po analizu LCC nasosnykh sistem. – M.: Soft Kom, 2010. – 220 s.
5. Kraev M.V., Ovsyannikov B.V., Shapiro A.S. Gidrodinamicheskie radial'nye uplotneniya vysokooborotnykh valov. – M.: Mashinostroenie, 1976. – 104 s.
6. Martsinkovskiy V.S., Ovseyko I.V., Skirdachenko E.I. Obespechenie germetichnosti tsentrobezhnykh nasosov khimicheskoy promyshlennosti. – Sumy: Khimich. i neftegaz. mashinostroenie, 2003. – S. 28–29.
7. Mannapov R.G. Otsenka nadezhnosti khimicheskogo i neftyanogo oborudovaniya pri poverkhnostnom razrushenii // Khimicheskoe i neftepererabatyvayushchee mashinostroenie, ser. KhM-1: obzornaya inform. – M.: TsINTIKhIMNEFTEMASh, 1988. – 39 s.
8. Makarov G.V. Uplotnitel'nye ustroystva. – Izd. 2-e, pererab. i dop. – L.: Mashinostroenie, 1973. – 232 s.
9. Pat. na poleznuyu model' 143464 Ros. Federatsiya, MPK F04D 13/06, F04D 9/04. Vertikal'nyy elektronasosnyy agregat / S.K. Bryunetkin, S.I. Dzarmotov, N.V. Kosyakova; patentoobladatel' OAO "Turbonasos". – № 2014107396/06; zayavl. 26.02.2014; opubl. 20.07.2014, Byul. № 20.
10. Semiduberskiy M.S. Nasosy, kompressory, ventilyatory: ucheb. dlya tekhnikumov. – 2-e izd., pererab. i dop. – M.: Vysshaya shk., 1961. – 288 s.
11. Tarel'nik V.B., Martsinkovskiy V.S. Modernizatsiya i remont rotornykh mashin: monogr. – Sumy: Kavkazskiy val, 2005. – 364 s.
12. Kondakov L.A., Golubev A.I., Ovander V.B. Uplotneniya i uplotnitel'naya tekhnika: sprav. – 2-e izd., pererab. i dop. – M.: Mashinostroenie, 1994. – S. 323–327.